欢迎访问《硅酸盐通报》官方网站,今天是
分享到:

硅酸盐通报 ›› 2021, Vol. 40 ›› Issue (4): 1220-1227.

• 水泥混凝土 • 上一篇    下一篇

我国现行规范中混凝土气泡参数计算方法的问题与建议

陈歆1, 李立辉2, 刘旭1, 田波2, 葛勇1   

  1. 1.哈尔滨工业大学交通科学与工程学院,哈尔滨 150090;
    2.交通运输部公路科学研究院,北京 100088
  • 收稿日期:2021-01-07 修回日期:2021-01-30 出版日期:2021-04-15 发布日期:2021-05-11
  • 通讯作者: 葛 勇,博士,教授。E-mail:hitbm@163.com
  • 作者简介:陈 歆(1991—),男,博士研究生。主要从事水泥混凝土耐久性的研究。E-mail:xin.chen@alu.hit.edu.cn
  • 基金资助:
    国家国际科技合作专项(ISTCP 2014DFR81000)

Problems and Suggestions on Computing Methods of Air-Void Characteristics of Concrete in Current Domestic Codes

CHEN Xin1, LI Lihui2, LIU Xu1, TIAN Bo2, GE Yong1   

  1. 1. School of Transportation Science and Engineering, Harbin Institute of Technology, Harbin 150090, China;
    2. Research Institute of Highway, Ministry of Transport, Beijing 100088, China
  • Received:2021-01-07 Revised:2021-01-30 Online:2021-04-15 Published:2021-05-11

摘要: 根据各气泡参数的几何意义,推导了基于直线导线法的混凝土气泡分布密度与气泡间距系数计算公式,复核了欧美与我国各现行规范中对气泡参数计算的规定,并对我国现行规范在该方面存在的问题提出了修正建议。复核发现,我国铁路、公路、水运与部分电力规范中对临界浆气比的取值为4.33,应改为4.34。公路规范所给出的气泡间距系数计算公式中部分系数存在错误,不符合气泡间距系数的几何意义。我国公路与水运规范中都没有注意到当含气量或含浆量取“%”为单位时,其值为以体积比比值表示时的100倍,若要保持计算公式中各项系数不变,应规定含气量与含浆量本身就是体积比比值。除铁路规范外,我国现行规范中还普遍存在计算气泡空间密度时误将1 mm3混凝土中气泡个数定义为1 000 mm3混凝土中的气泡个数以及在计算气泡间距系数(单位mm)时误将平均10 mm导线切割的气泡个数(单位cm-1)作为气泡频率(单位mm-1)代入计算公式的问题。以上问题都需要在各规范的下一次修编工作中重视与更正。

关键词: 混凝土, 气泡间距系数, 空间分布密度, 气泡频率, 临界浆气比

Abstract: Computing formulas of air-void spatial distribution density and air-void spacing factor of hardened concrete based on linear traverse method were derived according to geometric interpretations of the two parameters. By the comparison between derived formulas and regulations about air-void characteristics in foreign and domestic codes, current domestic codes were reviewed and revised. In the review, it is found that the critical ratio of cement paste content to air content is 4.33 in domestic codes of railway, highway, waterway and partial power industries. However, it is not as accurate as 4.34. Some coefficients in formula provided by domestic highway code are not in accordance with geometric interpretations. Both codes of highway and waterway industries do not realize that if the air content or paste content is presented as "%" by volume, it would be 100 times of the value of volume ratio and require formula coefficients changes. To keep formula coefficients unchanged, both the air content and paste content are suggested to be presented as values of volume ratio instead of "%" by volume. Except for railway codes, domestic codes of various industries mistakenly define the air-void number in 1 mm3 as air-void number in 1 000 mm3 in the calculation of spatial distribution density. These codes also mistakenly substitute the air-void number (unit: cm-1) intersected by 10 mm traverse for air-void frequency (unit: mm-1) in the calculation formula of spacing factor, the unit of which is millimeter. All the errors mentioned above need to be taken seriously and revised in future editions.

Key words: concrete, air-void spacing factor, spatial distribution density, air-void frequency, critical paste/air ratio

中图分类号: