无釉砖和有釉砖耐磨性标准的统一化探析

硅酸盐通报 ›› 2021, Vol. 40 ›› Issue (2): 616-621.

所属专题：陶瓷

无釉砖和有釉砖耐磨性标准的统一化探析

苏华枝^1,2, 余有根¹, 刘一军², 吴建青¹

1.华南理工大学材料科学与工程学院,广州 510641;
2.蒙娜丽莎集团股份有限公司博士后科研工作站,佛山 528211

收稿日期:2020-09-16 修回日期:2020-11-18 出版日期:2021-02-15 发布日期:2021-03-10
通讯作者: 吴建青,博士,教授。E-mail:imjqwu@scut.edu.cn
作者简介:苏华枝(1985—),男,博士,高工。主要从事陶瓷材料的研究。E-mail:imhzsu@qq.com

Unification of Abrasion Resistance Standard for Unglazed Tiles and Glazed Tiles

SU Huazhi^1,2, YU Yougen¹, LIU Yijun², WU Jianqing¹

1. School of Materials Science and Engineering, South China University of Technology, Guangzhou 510641, China;
2. Postdoctoral Research Center, Monalisa Group Co., Ltd., Foshan 528211, China

Received:2020-09-16 Revised:2020-11-18 Online:2021-02-15 Published:2021-03-10

摘要/Abstract

摘要： 耐磨性是陶瓷砖的一项关键性能指标,目前GB/T 4100—2015《陶瓷砖》规定无釉砖和有釉砖采用不同的试验方法。利用耐深度磨损试验机、陶瓷砖釉面耐磨试验机和Taber试验机对无釉砖和有釉砖进行耐磨性的测定,研究同一种试验方法是否能同时对两种陶瓷砖作精确的评判。结果表明,无釉砖耐磨深度法和Taber耐磨试验法可通过磨损体积的大小对无釉砖进行耐磨性的测定,但两者都不适合用于有釉砖耐磨性的测定。有釉砖表面耐磨法用磨耗质量大小取代目视评价可得到更客观和精准的结果,可同时用于无釉砖和有釉砖耐磨性的测定。

关键词: 陶瓷砖, 无釉砖, 有釉砖, 耐磨性, 磨耗, 标准

Abstract: Abrasion resistance is a key performance of ceramic tiles. At present, GB/T 4100—2015 "Ceramic tiles" requires that different test methods are used for unglazed tiles and glazed tiles. Abrasion resistance of unglazed tiles and glazed tiles were determined by deep abrasion equipment, surface abrasion apparatus and Taber abraser respectively. Whether the same test method can make accurate judgment on ceramic tiles was discussed. The results show that unglazed tiles can be determined by the method of resistance to deep abrasion for unglazed tiles and the method of relative resistance to wear of unglazed ceramic tiles by the Taber abraser. But neither of them is suitable for glazed tiles. Replacing visual evaluation with the loss in mass can get more objective and accurate results in the test method of resistance to surface abrasion for glazed tiles, and applicable to the determination of abrasion resistance for both unglazed tiles and glazed tiles.

Key words: ceramic tile, unglazed tile, glazed tile, abrasion resistance, abrasion loss, standard

中图分类号:

TQ174

苏华枝, 余有根, 刘一军, 吴建青. 无釉砖和有釉砖耐磨性标准的统一化探析[J]. 硅酸盐通报, 2021, 40(2): 616-621.

SU Huazhi, YU Yougen, LIU Yijun, WU Jianqing. Unification of Abrasion Resistance Standard for Unglazed Tiles and Glazed Tiles[J]. BULLETIN OF THE CHINESE CERAMIC SOCIETY, 2021, 40(2): 616-621.

参考文献

[1] 中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会.陶瓷砖:GB/T 4100—2015[S].北京:中国标准出版社,2015.
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration. Ceramic tiles: GB/T 4100—2015[S]. Bejing: Standards Press of China, 2015 (in Chinese).
[2] 黄惠宁.2019—2020年全球瓷砖产品与技术发展趋势[J].佛山陶瓷,2019,29(12):1-11.
HUANG H N. Porcelain tiles and technique development tendency in the world in 2019—2020[J]. Foshan Ceramics, 2019, 29(12): 1-11 (in Chinese).
[3] 夏凡.2018国际标准化组织ISO/TC189年会在巴西召开[DB/OL].2018-11-18.https://www.ceramicschina.com/PG_ViewNews_115426.html.
XIA F. The 2018 annual meeting of the international organization for standardization (ISO/TC189) was held in Brazil[DB/OL]. 2018-11-18. https://www.ceramicschina.com/PG_ViewNews_115426.html (in Chinese).
[4] 尹虹.第29届国际标准化组织ISO/TC189会议召开[DB/OL].2019-11-11.https://www.sohu.com/a/353148908_808775.
YIN H. The 29th international organization for standardization (ISO/TC189) conference was held[DB/OL]. 2019-11-11. https://www.sohu.com/a/353148908_808775 (in Chinese).
[5] 陶瓷砖釉面耐磨性试验方法:GB 11950—1989[S].
Test method for abrasion resistance of glazed tiles: GB 11950—1989[S] (in Chinese).
[6] 国家质量技术监督局.陶瓷砖试验方法第6部分:无釉砖耐磨深度的测定:GB/T 3810.6—1999[S].北京:中国标准出版社,2004.
The State Bureau of Quality and Technical Supervision. Test methods of ceramic tiles-Part 6: determination of resistance to deep abrasion for unglazed tiles: GB/T 3810.6—1999[S]. Beijing: Standards Press of China, 2004 (in Chinese).
[7] 中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会.陶瓷砖试验方法第6部分:无釉砖耐磨深度的测定:GB/T 3810.6—2016[S].北京:中国标准出版社,2017.
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration. Test methods of ceramic tiles-Part 6: determination of resistance to deep abrasion for unglazed tiles: GB/T 3810.6—2016[S]. Beijing: Standards Press of China, 2004 (in Chinese).
[8] 中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会.陶瓷砖试验方法第7部分:有釉砖表面耐磨性的测定:GB/T 3810.7—2016[S].北京:中国标准出版社,2017.
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration. Test methods of ceramic tiles-Part 7: determination of resistance to surface abrasion for glazed tiles: GB/T 3810.7—2016[S]. Beijing: Standards Press of China, 2017 (in Chinese).
[9] 吴汝莉.影响测定无釉陶瓷砖耐磨性压力调校的因素[J].广东建材,2007,23(11):169-170.
WU R L. Factors influencing the pressure adjustment for abrasion resistance of unglazed tiles[J]. Guangdong Building Materials, 2007, 23(11): 169-170 (in Chinese).
[10] 薛金,郭贵勇.无釉砖耐磨性能测定仪的试验原理及测量结果的分析研究[J].电子元器件与信息技术,2018,2(12):92-95.
XUE J, GUO G Y. Testing principle and measurement results analysis of resistance to abrasion for unglazed tiles determinator[J]. Electronic Component and Information Technology, 2018, 2(12): 92-95 (in Chinese).
[11] 曹阳,胡俊.论陶瓷地砖耐磨性的相关标准、技术要求与试验方法[J].佛山陶瓷,2013,23(6):1-4.
CAO Y, HU J. The standards, technical requirements and testing method of resistance to abrasion for ceramic floor tiles[J]. Foshan Ceramics, 2013, 23(6): 1-4 (in Chinese).
[12] 彭耀彬.陶瓷砖耐磨性与磨耗检测问题的探讨[J].建材与装饰,2019(36):64-65.
PENG Y B. Discussion on the abrasion resistance and abrasion detection of ceramic tiles[J]. Construction Materials & Decoration, 2019(36): 64-65 (in Chinese).
[13] 龚明,陈猛,张敏,等.陶瓷砖耐磨性与磨耗检测探讨与分析[J].陶瓷,2019(5):27-31.
GONG M, CHEN M, ZHANG M, et al. Discussion and research for resistance to abrasion and abrasion of dry pressed ceramic tiles[J]. Ceramics, 2019(5): 27-31 (in Chinese).
[14] 陆倩映,顾轩,何问慎,等.TABER耐磨试验机对不同样品的耐磨性研究[J].佛山陶瓷,2016,26(8):31-33+36.
LU Q Y, GU X, HE W S, et al. Study on abrasion resistance of TABLER abraser to different samples[J]. Foshan Ceramics, 2016, 26(8): 31-33+36 (in Chinese).
[15] Standard test method for abrasion resistance of dimension stone subjected to foot traffic using a rotary platform, double-head abraser: ASTM C1353—09[S].

无釉砖和有釉砖耐磨性标准的统一化探析

Unification of Abrasion Resistance Standard for Unglazed Tiles and Glazed Tiles

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	罗发胜, 李彬, 杜俊朋, 郭奕群, 麦俊明, 张同生. 骨料种类与级配对路面混凝土耐磨性能的影响[J]. 硅酸盐通报, 2022, 41(6): 1963-1972.
[2]	谢祥兵, 包梦, 李广慧, 史科, 李晗. 基于改进灰熵关联分析的混合型再生粗骨料评价指标及分级研究[J]. 硅酸盐通报, 2022, 41(1): 354-362.
[3]	黄法礼, 王振, 易忠来, 程欢, 温家馨, 袁政成, 靳昊, 李化建. 超细矿渣粉在水泥颗粒中的密实填充作用[J]. 硅酸盐通报, 2021, 40(8): 2647-2652.
[4]	王里, 李丹利, 叶珂含, 关景元, 冯舵. 水泥基复合材料3D可打印性的量化、优化及标准化[J]. 硅酸盐通报, 2021, 40(6): 1814-1820.
[5]	陶航宇, 陈萍, 龚亦凡, 詹静芳, 章莉. 基于砖含量的再生砖混粗骨料分类研究[J]. 硅酸盐通报, 2021, 40(3): 957-963.
[6]	汪伟, 张同生, 陈灿峰, 吴正德, 韦江雄, 余其俊. 可控低强度材料(CLSM)性能评价方法分析[J]. 硅酸盐通报, 2021, 40(11): 3634-3643.
[7]	王春福;王瑜玲;张飞燕. 建筑垃圾再生骨料强化改性研究进展[J]. 硅酸盐通报, 2020, 39(8): 2486-2491.
[8]	周磊磊;侯永利. 道路再生混凝土耐久性能研究进展[J]. 硅酸盐通报, 2020, 39(4): 1035-1042.
[9]	谢吉程, 张云, 杜越明, 陈正, 罗婷倚, 唐亚森. 机制砂混凝土耐磨性的主要影响因素分析及多因素计算模型[J]. 硅酸盐通报, 2020, 39(12): 3812-3822.
[10]	万炳彤;鲍学英;李爱春. 再生混凝土细骨料质量等级评价研究[J]. 硅酸盐通报, 2019, 38(9): 2758-276.
[11]	王佳磊;许宁;谢宇;沈超;浦旭清;陈介民;岳鹿. 掺杂不同稻壳灰对垃圾焚烧底灰基砌块的性能研究[J]. 硅酸盐通报, 2019, 38(6): 1818-182.
[12]	苏青;谢红波;陈哲;麦俊明;吴春丽. 利用废弃物锡矿尾砂制备陶瓷砖的研究[J]. 硅酸盐通报, 2019, 38(6): 1960-196.
[13]	冷政;曾维;李曦;蒋震;向佳瑜;刘哲. 200MPa级超高性能混凝土胶砂体系结构与性能研究[J]. 硅酸盐通报, 2019, 38(4): 1096-110.
[14]	周义鸿;干磊;李毓峰. 硅酸盐矿物标准熵简易计算模型[J]. 硅酸盐通报, 2019, 38(3): 743-748.
[15]	张苛;张争奇;罗要飞. 基于圆柱形芯样的沥青路面现场抗车辙性能评价标准[J]. 硅酸盐通报, 2018, 37(6): 1951-1959.